wuqiyang312
/
u8g2-copy
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
u8g2-copy/csrc/u8x8_d_ssd1305.c

515 lines
18 KiB
C
Raw Normal View History

started with ssd1305, bugfix issue #148
2017-01-06 22:49:15 +08:00
/*
u8x8_d_ssd1305.c
Universal 8bit Graphics Library (https://github.com/olikraus/u8g2/)
Copyright (c) 2017, olikraus@gmail.com
All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
* Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
* Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or other
materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#include "u8x8.h"
static const uint8_t u8x8_d_ssd1305_powersave0_seq[] = {
U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */
U8X8_C(0x0af), /* display on */
U8X8_END_TRANSFER(), /* disable chip */
U8X8_END() /* end of sequence */
};
static const uint8_t u8x8_d_ssd1305_powersave1_seq[] = {
U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */
U8X8_C(0x0ae), /* display off */
U8X8_END_TRANSFER(), /* disable chip */
U8X8_END() /* end of sequence */
};
ssd1305, issue #146
2017-01-07 04:18:46 +08:00
static const uint8_t u8x8_d_ssd1305_128x32_flip0_seq[] = {
started with ssd1305, bugfix issue #148
2017-01-06 22:49:15 +08:00
U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */
ssd1305, issue #146
2017-01-07 04:18:46 +08:00
U8X8_CA(0x0d3, 32), /* display offset to 32 */
started with ssd1305, bugfix issue #148
2017-01-06 22:49:15 +08:00
U8X8_C(0x0a1), /* segment remap a0/a1*/
U8X8_C(0x0c8), /* c0: scan dir normal, c8: reverse */
U8X8_END_TRANSFER(), /* disable chip */
U8X8_END() /* end of sequence */
};
ssd1305, issue #146
2017-01-07 04:18:46 +08:00
static const uint8_t u8x8_d_ssd1305_128x32_flip1_seq[] = {
started with ssd1305, bugfix issue #148
2017-01-06 22:49:15 +08:00
U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */
ssd1305, issue #146
2017-01-07 04:18:46 +08:00
U8X8_CA(0x0d3, 0), /* display offset to */
started with ssd1305, bugfix issue #148
2017-01-06 22:49:15 +08:00
U8X8_C(0x0a0), /* segment remap a0/a1*/
U8X8_C(0x0c0), /* c0: scan dir normal, c8: reverse */
U8X8_END_TRANSFER(), /* disable chip */
U8X8_END() /* end of sequence */
};
ssd1305, issue #146
2017-01-07 04:18:46 +08:00
static uint8_t u8x8_d_ssd1305_generic(u8x8_t *u8x8, uint8_t msg, uint8_t arg_int, void *arg_ptr)
{
uint8_t x, c;
uint8_t *ptr;
switch(msg)
{
case U8X8_MSG_DISPLAY_DRAW_TILE:
u8x8_cad_StartTransfer(u8x8);
x = ((u8x8_tile_t *)arg_ptr)->x_pos;
x *= 8;
x += u8x8->x_offset;
u8x8_cad_SendCmd(u8x8, 0x040 ); /* set line offset to 0 */
u8x8_cad_SendCmd(u8x8, 0x010 | (x>>4) );
u8x8_cad_SendArg(u8x8, 0x000 | ((x&15)));
u8x8_cad_SendArg(u8x8, 0x0b0 | (((u8x8_tile_t *)arg_ptr)->y_pos) );
do
{
c = ((u8x8_tile_t *)arg_ptr)->cnt;
ptr = ((u8x8_tile_t *)arg_ptr)->tile_ptr;
u8x8_cad_SendData(u8x8, c*8, ptr); /* note: SendData can not handle more than 255 bytes */
/*
do
{
u8x8_cad_SendData(u8x8, 8, ptr);
ptr += 8;
c--;
} while( c > 0 );
*/
arg_int--;
} while( arg_int > 0 );
u8x8_cad_EndTransfer(u8x8);
break;
case U8X8_MSG_DISPLAY_SET_POWER_SAVE:
if ( arg_int == 0 )
u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1305_powersave0_seq);
else
u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1305_powersave1_seq);
break;
#ifdef U8X8_WITH_SET_CONTRAST
case U8X8_MSG_DISPLAY_SET_CONTRAST:
u8x8_cad_StartTransfer(u8x8);
u8x8_cad_SendCmd(u8x8, 0x081 );
u8x8_cad_SendArg(u8x8, arg_int ); /* ssd1305 has range from 0 to 255 */
u8x8_cad_EndTransfer(u8x8);
break;
#endif
default:
return 0;
}
return 1;
}
started with ssd1305, bugfix issue #148
2017-01-06 22:49:15 +08:00
ssd1305, issue #146
2017-01-07 04:18:46 +08:00
/* timing from SSD1306 */
started with ssd1305, bugfix issue #148
2017-01-06 22:49:15 +08:00
static const u8x8_display_info_t u8x8_ssd1305_128x32_noname_display_info =
{
/* chip_enable_level = */ 0,
/* chip_disable_level = */ 1,
/* post_chip_enable_wait_ns = */ 20,
/* pre_chip_disable_wait_ns = */ 10,
/* reset_pulse_width_ms = */ 100, /* SSD1306: 3 us */
/* post_reset_wait_ms = */ 100, /* far east OLEDs need much longer setup time */
/* sda_setup_time_ns = */ 50, /* SSD1306: 15ns, but cycle time is 100ns, so use 100/2 */
/* sck_pulse_width_ns = */ 50, /* SSD1306: 20ns, but cycle time is 100ns, so use 100/2, AVR: below 70: 8 MHz, >= 70 --> 4MHz clock */
/* sck_clock_hz = */ 4000000UL, /* since Arduino 1.6.0, the SPI bus speed in Hz. Should be 1000000000/sck_pulse_width_ns */
/* spi_mode = */ 0, /* active high, rising edge */
/* i2c_bus_clock_100kHz = */ 4,
/* data_setup_time_ns = */ 40,
/* write_pulse_width_ns = */ 150, /* SSD1306: cycle time is 300ns, so use 300/2 = 150 */
/* tile_width = */ 16,
fix typo in comment
2023-03-06 03:45:34 +08:00
/* tile_height = */ 4,
ssd1305, issue #146
2017-01-07 04:18:46 +08:00
/* default_x_offset = */ 2,
/* flipmode_x_offset = */ 2,
started with ssd1305, bugfix issue #148
2017-01-06 22:49:15 +08:00
/* pixel_width = */ 128,
ssd1305, issue #146
2017-01-07 04:18:46 +08:00
/* pixel_height = */ 32
started with ssd1305, bugfix issue #148
2017-01-06 22:49:15 +08:00
};
ssd1305, issue #146
2017-01-07 04:18:46 +08:00
static const uint8_t u8x8_d_ssd1305_128x32_noname_init_seq[] = {
U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */
U8X8_C(0x0ae), /* display off */
U8X8_CA(0x0d5, 0x080), /* clock divide ratio (0x00=1) and oscillator frequency (0x8) */
U8X8_CA(0x0a8, 0x03f), /* multiplex ratio */
U8X8_CA(0x0d3, 32), /* display offset to 32 */
U8X8_C(0x040), /* set display start line to 0 */
issue #1362
2020-12-26 01:17:38 +08:00
U8X8_CA(0x020, 0x000), /* horizontal addressing mode */
ssd1305, issue #146
2017-01-07 04:18:46 +08:00
U8X8_C(0x0a1), /* segment remap a0/a1*/
U8X8_C(0x0c8), /* c0: scan dir normal, c8: reverse */
// Flipmode
// U8X8_C(0x0a0), /* segment remap a0/a1*/
// U8X8_C(0x0c0), /* c0: scan dir normal, c8: reverse */
U8X8_CA(0x0da, 0x012), /* com pin HW config, sequential com pin config (bit 4), disable left/right remap (bit 5) */
U8X8_CA(0x081, 0x0cf), /* [2] set contrast control */
U8X8_CA(0x0d9, 0x0f1), /* [2] pre-charge period 0x022/f1*/
U8X8_CA(0x0db, 0x040), /* vcomh deselect level */
// if vcomh is 0, then this will give the biggest range for contrast control issue #98
// restored the old values for the noname constructor, because vcomh=0 will not work for all OLEDs, #116
U8X8_C(0x02e), /* Deactivate scroll */
U8X8_C(0x0a4), /* output ram to display */
U8X8_C(0x0a6), /* none inverted normal display mode */
U8X8_END_TRANSFER(), /* disable chip */
U8X8_END() /* end of sequence */
};
started with ssd1305, bugfix issue #148
2017-01-06 22:49:15 +08:00
uint8_t u8x8_d_ssd1305_128x32_noname(u8x8_t *u8x8, uint8_t msg, uint8_t arg_int, void *arg_ptr)
{
ssd1305, issue #146
2017-01-07 04:18:46 +08:00
if ( u8x8_d_ssd1305_generic(u8x8, msg, arg_int, arg_ptr) != 0 )
return 1;
started with ssd1305, bugfix issue #148
2017-01-06 22:49:15 +08:00
switch(msg)
{
ssd1305, issue #146
2017-01-07 04:18:46 +08:00
case U8X8_MSG_DISPLAY_SET_FLIP_MODE:
if ( arg_int == 0 )
{
u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1305_128x32_flip0_seq);
u8x8->x_offset = u8x8->display_info->default_x_offset;
}
else
{
u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1305_128x32_flip1_seq);
u8x8->x_offset = u8x8->display_info->flipmode_x_offset;
}
break;
started with ssd1305, bugfix issue #148
2017-01-06 22:49:15 +08:00
case U8X8_MSG_DISPLAY_INIT:
u8x8_d_helper_display_init(u8x8);
u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1305_128x32_noname_init_seq);
break;
case U8X8_MSG_DISPLAY_SETUP_MEMORY:
u8x8_d_helper_display_setup_memory(u8x8, &u8x8_ssd1305_128x32_noname_display_info);
break;
default:
return 0;
}
return 1;
}
issue #2002
2022-11-23 03:51:16 +08:00
/*================================================*/
/* issue 2002: Waveshare */
#ifdef SAME_AS_ADAFRUIT
/* timing from SSD1306 */
static const u8x8_display_info_t u8x8_ssd1305_128x32_waveshare_display_info =
{
/* chip_enable_level = */ 0,
/* chip_disable_level = */ 1,
/* post_chip_enable_wait_ns = */ 20,
/* pre_chip_disable_wait_ns = */ 10,
/* reset_pulse_width_ms = */ 100, /* SSD1306: 3 us */
/* post_reset_wait_ms = */ 100, /* far east OLEDs need much longer setup time */
/* sda_setup_time_ns = */ 50, /* SSD1306: 15ns, but cycle time is 100ns, so use 100/2 */
/* sck_pulse_width_ns = */ 50, /* SSD1306: 20ns, but cycle time is 100ns, so use 100/2, AVR: below 70: 8 MHz, >= 70 --> 4MHz clock */
/* sck_clock_hz = */ 4000000UL, /* since Arduino 1.6.0, the SPI bus speed in Hz. Should be 1000000000/sck_pulse_width_ns */
/* spi_mode = */ 0, /* active high, rising edge */
/* i2c_bus_clock_100kHz = */ 4,
/* data_setup_time_ns = */ 40,
/* write_pulse_width_ns = */ 150, /* SSD1306: cycle time is 300ns, so use 300/2 = 150 */
/* tile_width = */ 16,
fix typo in comment
2023-03-06 03:45:34 +08:00
/* tile_height = */ 4,
issue #2002
2022-11-23 03:51:16 +08:00
/* default_x_offset = */ 4,
/* flipmode_x_offset = */ 0,
/* pixel_width = */ 128,
/* pixel_height = */ 32
};
uint8_t u8x8_d_ssd1305_128x32_waveshare(u8x8_t *u8x8, uint8_t msg, uint8_t arg_int, void *arg_ptr)
{
if ( u8x8_d_ssd1305_generic(u8x8, msg, arg_int, arg_ptr) != 0 )
return 1;
switch(msg)
{
case U8X8_MSG_DISPLAY_SET_FLIP_MODE:
if ( arg_int == 0 )
{
u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1305_128x32_flip0_seq);
u8x8->x_offset = u8x8->display_info->default_x_offset;
}
else
{
u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1305_128x32_flip1_seq);
u8x8->x_offset = u8x8->display_info->flipmode_x_offset;
}
break;
case U8X8_MSG_DISPLAY_INIT:
u8x8_d_helper_display_init(u8x8);
u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1305_128x32_noname_init_seq);
break;
case U8X8_MSG_DISPLAY_SETUP_MEMORY:
u8x8_d_helper_display_setup_memory(u8x8, &u8x8_ssd1305_128x32_waveshare_display_info);
break;
default:
return 0;
}
return 1;
}
#endif
issue #724
2018-10-17 02:49:07 +08:00
/*================================================*/
/* adafruit 128x32 SSD1305 OLED, https://www.adafruit.com/product/2675 */
/* issue 724 */
/* timing from SSD1306 */
static const u8x8_display_info_t u8x8_ssd1305_128x32_adafruit_display_info =
{
/* chip_enable_level = */ 0,
/* chip_disable_level = */ 1,
/* post_chip_enable_wait_ns = */ 20,
/* pre_chip_disable_wait_ns = */ 10,
/* reset_pulse_width_ms = */ 100, /* SSD1306: 3 us */
/* post_reset_wait_ms = */ 100, /* far east OLEDs need much longer setup time */
/* sda_setup_time_ns = */ 50, /* SSD1306: 15ns, but cycle time is 100ns, so use 100/2 */
/* sck_pulse_width_ns = */ 50, /* SSD1306: 20ns, but cycle time is 100ns, so use 100/2, AVR: below 70: 8 MHz, >= 70 --> 4MHz clock */
/* sck_clock_hz = */ 4000000UL, /* since Arduino 1.6.0, the SPI bus speed in Hz. Should be 1000000000/sck_pulse_width_ns */
/* spi_mode = */ 0, /* active high, rising edge */
/* i2c_bus_clock_100kHz = */ 4,
/* data_setup_time_ns = */ 40,
/* write_pulse_width_ns = */ 150, /* SSD1306: cycle time is 300ns, so use 300/2 = 150 */
/* tile_width = */ 16,
fix typo in comment
2023-03-06 03:45:34 +08:00
/* tile_height = */ 4,
issue #724
2018-10-29 01:03:37 +08:00
/* default_x_offset = */ 4,
issue #724
2018-10-17 02:49:07 +08:00
/* flipmode_x_offset = */ 0,
/* pixel_width = */ 128,
/* pixel_height = */ 32
};
uint8_t u8x8_d_ssd1305_128x32_adafruit(u8x8_t *u8x8, uint8_t msg, uint8_t arg_int, void *arg_ptr)
{
if ( u8x8_d_ssd1305_generic(u8x8, msg, arg_int, arg_ptr) != 0 )
return 1;
switch(msg)
{
case U8X8_MSG_DISPLAY_SET_FLIP_MODE:
if ( arg_int == 0 )
{
u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1305_128x32_flip0_seq);
u8x8->x_offset = u8x8->display_info->default_x_offset;
}
else
{
u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1305_128x32_flip1_seq);
u8x8->x_offset = u8x8->display_info->flipmode_x_offset;
}
break;
case U8X8_MSG_DISPLAY_INIT:
u8x8_d_helper_display_init(u8x8);
u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1305_128x32_noname_init_seq);
break;
case U8X8_MSG_DISPLAY_SETUP_MEMORY:
u8x8_d_helper_display_setup_memory(u8x8, &u8x8_ssd1305_128x32_adafruit_display_info);
break;
default:
return 0;
}
return 1;
}
ssd1305 128x64, issue #521
2018-02-27 01:24:10 +08:00
/*================================================*/
/* adafruit SSD1305 OLED */
/* timing from SSD1306 */
static const u8x8_display_info_t u8x8_ssd1305_128x64_adafruit_display_info =
{
/* chip_enable_level = */ 0,
/* chip_disable_level = */ 1,
/* post_chip_enable_wait_ns = */ 20,
/* pre_chip_disable_wait_ns = */ 10,
/* reset_pulse_width_ms = */ 100, /* SSD1306: 3 us */
/* post_reset_wait_ms = */ 100, /* far east OLEDs need much longer setup time */
/* sda_setup_time_ns = */ 50, /* SSD1306: 15ns, but cycle time is 100ns, so use 100/2 */
/* sck_pulse_width_ns = */ 50, /* SSD1306: 20ns, but cycle time is 100ns, so use 100/2, AVR: below 70: 8 MHz, >= 70 --> 4MHz clock */
/* sck_clock_hz = */ 4000000UL, /* since Arduino 1.6.0, the SPI bus speed in Hz. Should be 1000000000/sck_pulse_width_ns */
/* spi_mode = */ 0, /* active high, rising edge */
/* i2c_bus_clock_100kHz = */ 4,
/* data_setup_time_ns = */ 40,
/* write_pulse_width_ns = */ 150, /* SSD1306: cycle time is 300ns, so use 300/2 = 150 */
/* tile_width = */ 16,
fix typo in comment
2023-03-06 03:45:34 +08:00
/* tile_height = */ 8,
ssd1305 128x64, issue #521
2018-02-27 01:24:10 +08:00
/* default_x_offset = */ 2,
/* flipmode_x_offset = */ 2,
/* pixel_width = */ 128,
/* pixel_height = */ 64
};
static const uint8_t u8x8_d_ssd1305_128x64_adafruit_init_seq[] = {
U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */
U8X8_C(0x0ae), /* display off */
U8X8_CA(0x0d5, 0x0f0), /* clock divide ratio (0x00=1) and oscillator frequency */
U8X8_CA(0x0a8, 0x03f), /* multiplex ratio */
U8X8_CA(0x0d3, 0x040), /* display offset to 32 */
U8X8_C(0x040), /* set display start line to 0 */
issue #1362
2020-12-26 01:17:38 +08:00
U8X8_CA(0x020, 0x000), /* horizontal addressing mode */
ssd1305 128x64, issue #521
2018-02-27 01:24:10 +08:00
U8X8_C(0x0a1), /* segment remap a0/a1*/
U8X8_C(0x0c8), /* c0: scan dir normal, c8: reverse */
// Flipmode
// U8X8_C(0x0a0), /* segment remap a0/a1*/
// U8X8_C(0x0c0), /* c0: scan dir normal, c8: reverse */
U8X8_CA(0x0da, 0x012), /* com pin HW config, sequential com pin config (bit 4), disable left/right remap (bit 5) */
U8X8_CA(0x081, 0x032), /* [2] set contrast control */
U8X8_CA(0x082, 0x080), /* set area brightness (reset=0x080) */
U8X8_CA(0x0d9, 0x0f1), /* [2] pre-charge period 0x022/f1*/
U8X8_CA(0x0db, 0x040), /* vcomh deselect level */
// if vcomh is 0, then this will give the biggest range for contrast control issue #98
// restored the old values for the noname constructor, because vcomh=0 will not work for all OLEDs, #116
U8X8_C(0x02e), /* Deactivate scroll */
U8X8_C(0x0a4), /* output ram to display */
U8X8_C(0x0a6), /* none inverted normal display mode */
U8X8_END_TRANSFER(), /* disable chip */
U8X8_END() /* end of sequence */
};
uint8_t u8x8_d_ssd1305_128x64_adafruit(u8x8_t *u8x8, uint8_t msg, uint8_t arg_int, void *arg_ptr)
{
if ( u8x8_d_ssd1305_generic(u8x8, msg, arg_int, arg_ptr) != 0 )
return 1;
switch(msg)
{
case U8X8_MSG_DISPLAY_SET_FLIP_MODE:
if ( arg_int == 0 )
{
u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1305_128x32_flip0_seq);
u8x8->x_offset = u8x8->display_info->default_x_offset;
}
else
{
u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1305_128x32_flip1_seq);
u8x8->x_offset = u8x8->display_info->flipmode_x_offset;
}
break;
case U8X8_MSG_DISPLAY_INIT:
u8x8_d_helper_display_init(u8x8);
u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1305_128x64_adafruit_init_seq);
break;
case U8X8_MSG_DISPLAY_SETUP_MEMORY:
u8x8_d_helper_display_setup_memory(u8x8, &u8x8_ssd1305_128x64_adafruit_display_info);
break;
default:
return 0;
}
return 1;
}
issue #1111
2020-10-26 20:38:21 +08:00
/*================================================*/
/* Raystar RET012864 OLED, issue https://github.com/olikraus/u8g2/issues/1111 */
static const u8x8_display_info_t u8x8_ssd1305_128x64_raystar_display_info =
{
/* chip_enable_level = */ 0,
/* chip_disable_level = */ 1,
/* post_chip_enable_wait_ns = */ 20,
/* pre_chip_disable_wait_ns = */ 10,
/* reset_pulse_width_ms = */ 100, /* SSD1306: 3 us */
/* post_reset_wait_ms = */ 100, /* far east OLEDs need much longer setup time */
/* sda_setup_time_ns = */ 50, /* SSD1306: 15ns, but cycle time is 100ns, so use 100/2 */
/* sck_pulse_width_ns = */ 50, /* SSD1306: 20ns, but cycle time is 100ns, so use 100/2, AVR: below 70: 8 MHz, >= 70 --> 4MHz clock */
/* sck_clock_hz = */ 4000000UL, /* since Arduino 1.6.0, the SPI bus speed in Hz. Should be 1000000000/sck_pulse_width_ns */
/* spi_mode = */ 0, /* active high, rising edge */
/* i2c_bus_clock_100kHz = */ 4,
/* data_setup_time_ns = */ 40,
/* write_pulse_width_ns = */ 150, /* SSD1306: cycle time is 300ns, so use 300/2 = 150 */
/* tile_width = */ 16,
fix typo in comment
2023-03-06 03:45:34 +08:00
/* tile_height = */ 8,
issue #1111
2020-10-26 20:38:21 +08:00
/* default_x_offset = */ 4,
/* flipmode_x_offset = */ 0,
/* pixel_width = */ 128,
/* pixel_height = */ 64
};
uint8_t u8x8_d_ssd1305_128x64_raystar(u8x8_t *u8x8, uint8_t msg, uint8_t arg_int, void *arg_ptr)
{
if ( u8x8_d_ssd1305_generic(u8x8, msg, arg_int, arg_ptr) != 0 )
return 1;
switch(msg)
{
case U8X8_MSG_DISPLAY_SET_FLIP_MODE:
if ( arg_int == 0 )
{
u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1305_128x32_flip0_seq);
u8x8->x_offset = u8x8->display_info->default_x_offset;
}
else
{
u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1305_128x32_flip1_seq);
u8x8->x_offset = u8x8->display_info->flipmode_x_offset;
}
break;
case U8X8_MSG_DISPLAY_INIT:
u8x8_d_helper_display_init(u8x8);
u8x8_cad_SendSequence(u8x8, u8x8_d_ssd1305_128x64_adafruit_init_seq);
break;
case U8X8_MSG_DISPLAY_SETUP_MEMORY:
u8x8_d_helper_display_setup_memory(u8x8, &u8x8_ssd1305_128x64_raystar_display_info);
break;
default:
return 0;
}
return 1;
}